Download Driver Laptop Dell Vostro 3360 Latest

By Leonars

Download Driver Laptop Dell Vostro 3360 Install Update

Trademarks used in this text: Contents Notes, Cautions, and Warnings Assigning a System Password and Setup Password Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Close the display and turn the computer upside-down on a flat work surface.

To avoid damaging the system board, you must remove the main battery before you service the computer. Remove the main battery. Turn the computer top-side up. After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. To avoid damage to the computer, use only the battery designed for this particular Dell computer.

Do not use batteries designed for other Dell computers. Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Follow the procedures in Press in on the SD card to release it from the computer. Slide the SD card out of the computer. Installing the Battery Slide the battery into its slot until it clicks into place.

After Working Inside Your Computer. Follow the procedures in Remove the battery. Press in on the ExpressCard and release. Pull the ExpressCard and remove out of the computer. Slide the cover outwards to release it from the notches on the computer. Lift the cover upwards and away from the computer. Installing the Base Cover Align the edge of the base cover on the computer and slide it on the computer.

Tighten the screw s to secure the base cover to the computer. Use a flat-headed screw driver to pry the optical drive out of the computer. Slide the optical drive outwards and remove it from the computer. Remove the screws that secure the optical-drive bracket.

Remove the optical-drive bracket from the optical drive. Installing the Optical Drive Replace the optical-drive bracket and tighten the screws that secure the optical drive to the optical-drive bracket.

Slide the optical drive into the compartment on the chassis. Tighten the screw to secure the optical drive to the computer. Lift up the hard drive and remove from the computer. Remove the screws that secure the hard-drive bracket to the hard drive. Lift up and remove the hard drive from the hard drive bracket. Installing the Hard Drive Place the hard drive module into the hard drive bracket. Tighten the screws that secures the hard drive bracket to the hard drive.

Pull the tab and place the hard drive on the chassis. Tighten the screws that secure hard drive to the computer. Lift the clip to release the keyboard cable and disconnect it from the system board. Lift the clip to release the backlit cable and disconnect it from the system board. Installing the Keyboard Connect the keyboard data cable to the back of the keyboard.

Connect the backlit cable to the system board. Insert the keyboard in its compartment. Press down until the keyboard clicks into place. Push to release the hinge cover from the computer. Flip the computer and carefully remove the display hinge cover from the computer. Installing the Display Hinge Cover Replace the display hinge cover back to the computer till the latches are fixed into place.

Tighten the screws that secure the display hinge cover to the computer. Remove the screws from the bottom of the computer. Disconnect the LEDs fingerprint cable. Remove the screws that secures palmrest assembly in place. Lift the latch and disconnect the power button fingerprint cable.

Lift the tab and release the touchpad cable, SD card reader cable, and fingerprint scanner cable from the computer. Lift the tab and disconnect the functions button cable from the system.

Carefully pry up the palmrest along the edges. Slide the palmrest outwards and lift to remove from the computer. Installing the Palmrest Starting from the edges of the palmrest, press downwards on the palmrest to engage the tabs on the computer. Tighten the screws to secure the palmrest to the front of the computer. Connect the functions button cable to the system board. Connect the touchpad cable, SD card reader cable, and fingerprint scanner cable to the system board.

Remove the screws that secure the express card reader in place. Lift up and remove the express card reader from the system. Installing the Express Card Reader Place the express card reader into its slot on the chassis.

Tighten the screws to secure the express card reader to the computer. Connect the express card reader cable. Installing the Speakers Place the speakers on the computer and thread the speakers cable through the routing tabs.

Tighten the screws to secure the speakers in place. Connect the speaker cable. SD card reader Disconnect the system fan cable and the power cable. Disconnect the speaker cable.

Disconnect the Express card reader fingerprint cable. Disconnect the touchpad cable. Peel off the tape and disconnect the LVDS and camera cable. Remove the screws that secure the system board to the chassis. Lift up the system board from the chassis. Slide the system board towards right and remove from the chassis.

Installing the System Board Align the system board to the port connectors and place the system board in the computer. Tighten the screws to secure the system board to the chassis.

Affix the tape and connect the LVDS and camera cable. Connect the touchpad cable. Remove the screws that secure the heat sink to the system board. Lift up and remove the heat sink from the system board.

Installing the Heat Sink Tighten the screws to secure the heat sink to the system board. Connect the system fan cable to the system board. Remove the processor cover and lift the processor from the socket. Place it in an antistatic package. Installing the Processor Insert the processor into the processor socket.

Ensure the processor is properly seated. Replace the processor cover. Use a screw driver to release the coin-cell battery from the socket. The battery pops-out, lift and remove the battery from the socket. Installing the Coin-Cell Battery Insert the coin-cell battery into the slot.

Press on the coin-cell battery until it secures into place. Follow the procedures in Remove the: Pull out and remove the LAN board from the system. Tighten the screws to secure the LAN board to the chassis. Lift up and remove the SD card reader from the system.

Tighten the screw to secure the SD card reader to the computer. Remove the screws present below the display hinge cover.

Download Driver Laptop Dell Vostro 3360

Drivers para Dell Vostro 3360

Trademarks used in this text: Contents Notes, Cautions, and Warnings Assigning a System Password and Setup Password Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Close the display and turn the computer upside-down on a flat work surface. To avoid damaging the system board, you must remove the main battery before you service the computer. Remove the main battery.

Bluetooth not working on Dell Vostro 3360

Download Driver Laptop Dell Vostro 3360

Hello, I have a problem with bluetooth on my Dell Vostro , and I hope you could help me. The notebook can't find bluetooth devices and bluetooth devices can't find the notebook. Additionally, trying to turn off the BT adapter from context menu or from mobility center does not work as well. Tried updating the drivers, didn't work. Windows 7 bit Any ideas? More about bluetooth working dell vostro The BT adapter itself is working without a doubt I tried using it with ubuntu livecd and it was working perfectly. Hi, See if it does help: How to make bluetooth work in dell vostro notebook. Can't find your answer?

0 thoughts on “Download Driver Laptop Dell Vostro 3360

Leave a Reply

Your email address will not be published. Required fields are marked *